WIRELESS RECEIVERS
EDRJW - J1939 - Wireless Combo Receiver Control System
- Up to 8 Wireless Inputs & Up to 8 Hard Wired Inputs
- Smart Engine Start/Stop - One Input Control
- Set RPM/E-Pump Control - One Input Control
- 3 Programable Set Speeds & Variable RPM Increase/Decrease
- Foot/Hand Throttle Control
- Auto Neutral
- Cab Throttle Inhibit
- On Board Programming
- LED Light Diagnosing
- Plug and Play Harnesses Available
TESS604 -TESS 1 V2 Wireless Receiver
This is a replacement for the previous TESS203/303 systems. It is the same size and has the same 10 Pin connector as the TESS203/303. It will controls the engines Starting and Stopping, set RPM and E-pump. It will not work with the previous TESS204 transmitter, you need to use either the TESS504, 433T4 or 433T8 transmitter. Programming the transmitters to connect to the receiver is made easy and is done on the PCB. The transmitter have a range of approximately 200 feet depending on any physical obstruction that might impede the signal reception.
TESS603 -TESS 1 V2 Wireless Receiver
This receiver is used to control the engine start, engine stop, set RPM and emergency pump. You would use the following transmitters with this receiver, TESS504, 433T4 and 433T8. Programming the transmitters to connect to the receiver is made easy and is done on the PCB. The transmitter have a range of approximately 200 feet depending on any physical obstruction that might impede the signal reception.
TESS602 - TESS 1 V2 Wireless Receiver
This receiver has a four pin connector that is set up for power, ground and two momentary output channels. The TESS502 or 433T2 transmitters can be used with this product. Programming the transmitters to connect to the receiver is made easy and is done on the PCB. The transmitter have a range of approximately 200 feet depending on any physical obstruction that might impede the signal reception.
WORCS201 - Wireless Output Remote Control System
This is the wireless receiver that take will up to 8 wireless inputs. It works with 433T series and the TESS5 series transmitter. It is easy to program a transmitter to this receiver. The enclosure measures 4" X 4" X 2".
WIRELESS TRANSMITTERS
433T8 - 8 BUTTON HAND HELD TRANSMITTER
This fob can be configured with 1 to 8 buttons to control up to 8 different receiver outputs. It can be programmed for either a latched or momentary output. The label can be customized to show what each button that is used for. The range for the transmitter is roughly 1000' (300m). The unit operates from a single 3V CR2030 button cell battery. The transmitter works on a 433.92 MHZ and is pre-certified for FCC Part 15. The body of the transmitter measures 2.81" high by 1.62" wide. Will work with any of the wireless receivers.
433T(1-5) - 1 TO 5 BUTTON HAND HELD TRANSMITTER
This fob can be configured with 1 to 5 buttons to control up to 5 different receiver outputs. It can be programmed for either a latched or momentary output. The label can be customized to show what each button that is used for. The range for the transmitter is roughly up to 750' (230m). The unit operates from a single 3V CR2030 button cell battery. The transmitter works on a 433.92 MHZ and is pre-certified for FCC Part 15. The body of the transmitter measures 2.5" high by 1.37" wide. Will work with any of the wireless receivers.
TESS504 - 4 BUTTON WIRELESS TRANSMITTER
The TESS504 is used to control 4 functions, Engine Start, Engine Stop, Set RPM and Emergency Pump. Mostly used in the Utility field for Bucket or Digger Derek trucks. The range for the transmitter is roughly 1000' (300m). The unit operates from a single 3.6V 1/2 AA battery. The transmitter works on a 433.92 MHZ and is pre-certified for FCC Part 15. The body of the transmitter measures 4" X 4" X 2" enclosure. Works with the TESS603 & TESS604 receiver.
TESS502 - 2 BUTTON TRANSMITER
The TESS502 is used with the EDRJW series to control the engine start & stop with one button and the other button will control the engine set RPM and emergency pump. The range for the transmitter is roughly 1000' (300m). The unit operates from a single 3.6V 1/2 AA battery. The transmitter works on a 433.92 MHZ and is pre-certified for FCC Part 15. The body of the transmitter measures 4" X 4" X 2" enclosure.